This is an unvented gas-fi red heater. It uses air (oxygen) from the room in which it is installed. Provisions for adequate combustion and ventilation
10 23D8036WHBTU/Hr = BTU/Hr = WARNINGThe following formula can be used to determine the maximum heater rating per the definition of unconfined space:
23D8036 1133"151/4"223/4"237/8"BA9"Minimum9"Minimum42"MinimumCLEARANCES AND HEIGHT REQUIREMENTSNOTE: Clearances ar
12 23D803610"12"14"26"8"12"10"8"6"21/2"HoodNo combustible materials within 8” of opening. Do not co
23D8036 13CombustibleMaterialNon-combustibleMaterial5"1”CLEARANCES and HEIGHT REQUIREMENTSThe gas log heater must be installed at least 5"
14 23D8036225/8"331/2"16"331/2"16"331/2"271/2"225/8"317/8"REF16"371/4"453/4"153/8" 3
23D8036 15NOTE: Clearance requirements as detailed in “Clearances and Height Requirements” section of this manual must be met before securing heater
16 23D8036NOTICE: A qualifi ed gas appliance installer must connect the heater to the gas supply. Consult all local codes.IMPORTANT: Loosen the pipe
23D8036 17To reach factory installed flex line, go through access door on right or left side of firebox. CONNECTING THE GASCHECK GAS TYPE: The gas su
18 23D8036CHECKING GAS PRESSURETest all gas joints from the gas meter to the heater valve for leaks using a gas analyzer or soap and water solution a
23D8036 19ELECTRICAL WIRING (MILLI-VOLT)The milli-volt valve is a self-powered combination gas control THAT DOES NOT REQUIRE 110 VAC TO OPERATE.Figur
2 23D8036CONTENTSImportant Safety Information ...3Product Features ...
20 23D8036ELECTRICAL WIRING (MILLI-VOLT)A. COMPLETE MILLIVOLT SYSTEM CHECK (“A” Reading - Thermostat contacts CLOSED - Control Knob “ON” - Main b
23D8036 21ELECTRICAL WIRING (FAN)If any of the original wire as supplied with the fireplace must be replaced, contact dealer for proper replacement w
22 23D8036 LOG PLACEMENTFigure 19 - Installing Right Base Log (#1)Before you begin — This unit is supplied with six (6) ceramic fi ber logs. Do n
23D8036 23LOG PLACEMENTFigure 21 - Installing Left Base Log (#3)Left Base Log (#3) Pins Figure 22 - Installing Right Top Log (#4)Right top log (#4)Pi
24 23D8036LOG PLACEMENTFigure 23 - Installing Left Top Log (#5)Left Top Log(#5)5. Place right end of left top log (#5) on bottom center grate pin. R
23D8036 25LOG PLACEMENT6. Place right front log (#6) on two pins on the right front of grate. See Figure 25.Figure 25 - Installing Right Front Log (
26 23D8036FLAME APPEARANCEFlames from the pilot, front and rear burner should be visually checked as soon as the heater is installed. In addition, pe
23D8036 27In normal operation at full rate after 15 minutes, the following flame appearances should be observed:Figure 33 - Correct Appearance of Rea
28 23D8036WARNINGFigure 34 - Location of Piezo Ignitor, Control Knobs and Switch on Milli-Volt Unit, Hi/Lo Remote Control and Manual Unit A. This ap
23D8036 29OPERATING INSTRUCTIONS 1. STOP! Read the safety information label. 2. Make sure the manual shutoff valve is fully open. 3. This gas l
23D8036 39. The installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.l/NFPA54.1
30 23D8036 1. Remove any items necessary for easy access to the pilot (for example: logs, screens, etc.). 2. Follow appropriate lighting instruc
23D8036 31Annual inspection and cleaning by your dealer or qualified service technician is recommended to prevent malfunction and/or sooting.PERIODIC
32 23D8036OBSERVED PROBLEMWhen ignitor button is pressed, there is no spark at ODS/pilot.Appliance produces unwanted odors.Appliance shuts off during
23D8036 33OBSERVED PROBLEMODS/pilot lights, but flame goes out when control knob is released.Burner does not light after ODS/pilot is lit.Burner back
34 23D80361234888888137561412Failure to position the parts in accordance with these diagrams or failure to use only parts specifi cally approved with
23D8036 35REPLACEMENT PARTS LIST Item Qty Description DIS33N/P 1 1 Screen Assembly 23D8028 2 1 Canopy Assembly 23D8027 3 3 Top Black Lo
36 23D803656348A8B127ILLUSTRATED PARTS BREAKDOWN Failure to position the parts in accordance with these diagrams or failure to use only parts specifi
23D8036 37REPLACEMENT PARTS LIST REPLACEMENT PARTS ARE AVAILABLE THROUGH YOUR RETAILER. Item Description Qty 33ISDN 33ISDP Common Parts 1 Pie
38 23D8036#2#1#3#4#5#6REPLACEMENT PARTS ARE AVAILABLE THROUGH YOUR RETAILER. ILLUSTRATED PARTS BREAKDOWN Failure to position the parts in accordance
23D8036 39NOTES
4 23D8036IMPORTANT SAFETY INFORMATIONContinued from page 316. Keep room area clear and free from combustible materi-als, gasoline and other flammable
MAY 2006 P/N 23D8036 • Rev. 1LIMITED LIFETIME WARRANTY POLICYThe following components are warranted for life to the original owner, subject of proof
23D8036 5Your vent-free fireplace must be mounted to the floor or the fireplace hearth.OPERATIONThis unvented gas heater requires no outside venting
6 23D8036NATURAL GAS Milli-Volt and T-Stat Pressure Regulator Pressure Setting: 3.5" w.c. Pilot Regulator: 3.5" w.c. Gas Inlet Pressure: Ma
23D8036 7GETTING STARTED MAKE SURE YOU HAVE RECEIVED ALL PARTSCheck your packing list to verify that all listed parts have been received. You should
8 23D8036REMOVING SCREENRemove fireplace screen by pushing screen frame panel up and out. See Figure 2.Figure 2 - Removing Fireplace ScreenGENERAL IN
23D8036 9GENERAL INSTALLATION INFORMATIONCODESAdhere to all local codes or, in their absence, the latest edition of THE NATIONAL FUEL GAS CODE ANSI Z
Commentaires sur ces manuels